Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
Listed here in the next paragraph you will discover a lot of incredibly good information in relation to Tools You Need to Install a New Bathtub .
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately tough job. If the old bathtub is conveniently available, the job can relocate speedily; if you have to open up a wall surface to get rid of the old tub as well as position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have actually certified yourself for the job as well as are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your shower room if you have actually currently bought a brand-new tub and don't need to alter the plan of your previous water system pipelines.
Your devices as well as product checklist must make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipes. Once the supply pipelines have actually been eliminated, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former type needs to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using the two wood boards under its feet, place the tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bathtub has been used at least when as this will certainly resolve it into its final position.
Preparing for the Installation
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealer can crack relatively early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the search engines. Sharing is caring. You won't know, you will be helping someone out. I am grateful for your time. Come back soon.
This Page
Report this page